Forum unknown
· General
#BBS
9 messages in this thread
HELLO, MY NAME IS ROBERT HARTWIG I AM INTERESTED IN A POSSIBLE LOCAL BBS IN
JACKSONVILLE,FLA. I WOULD LIKE TO RUN ONE CENTERED AROUND ACAD AND ASSOCIATED
TOPICS LSP,AFLIX,BLOCKS ECT. CAN YOU GIVE ME SOME INFORMATION ON RUNNING SUCH
A BOARD. IF SO, I WILL BE ATTENDING A/E/C SYSTEMS MAY 4 & 5TH ANY POSSIBLE
FORUMS OR SYOPS MEETINGS?? ROBERT…
Well, I sometimes get to talk to the AEC class, so perhaps then. As for the
starting a BBS you should investigate the IBM Communications Forum.
(GO IBMCOM) I think they have a section set aside just for the purpose.
Good luck with your BBS, also there is a list of them in DL9.
Jamie
Robert, I have just switched to the ATO software for interfacing with CIS
forums. It is an easy to use program that really does make life here alot
easier. If you GO IBMNEW you'll find help and access to the ATO program.
Good Luck, Dennis
Robert, I have just switched to the ATO software for interfacing with CIS
forums. It is an easy to use program that really does make life here alot
easier. If you GO IBMNEW you'll find help and access to the ATO program.
Good Luck, Dennis
Well, I sometimes get to talk to the AEC class, so perhaps then. As for the
starting a BBS you should investigate the IBM Communications Forum.
(GO IBMCOM) I think they have a section set aside just for the purpose.
Good luck with your BBS, also there is a list of them in DL9.
Jamie
HI, I'm doing what your asking about here in San Diego,CA and have a couple
of suggestions if you don't mind. The best software I'v found for a bbs is
either Collie(old but very simple to use for both the sysop and the user)
Wildcat ( newer and a little complex for sysop but again easy for end users)
both are share ware and can be found in the IBM com area here on CIS. Also
get a complete Procomm setup from same place and give it away to your users.
If you want to either EasyPlex me, call me at LightSpeed Corp. (619)697-2210
or leave a message on our BBS (619) 697-9840 (300/1200/2400)
Corky Deeds LightSpeed Corp.
HI, I'm doing what your asking about here in San Diego,CA and have a couple
of suggestions if you don't mind. The best software I'v found for a bbs is
either Collie(old but very simple to use for both the sysop and the user)
Wildcat ( newer and a little complex for sysop but again easy for end users)
both are share ware and can be found in the IBM com area here on CIS. Also
get a complete Procomm setup from same place and give it away to your users.
If you want to either EasyPlex me, call me at LightSpeed Corp. (619)697-2210
or leave a message on our BBS (619) 697-9840 (300/1200/2400)
Corky Deeds LightSpeed Corp.
Robert,
We here in Orlando have a nice AutoCAD BBS that doesn't get used enough. You
can contact the SYSOP, Mark Starr, at (305) 682 4430. After about 5:30 or 6
PM, that number becomes the BBS and you can reach him that way also. I'm
sure he'd be glad to pass on do's and don'ts, hints, etc.
Robert,
We here in Orlando have a nice AutoCAD BBS that doesn't get used enough. You
can contact the SYSOP, Mark Starr, at (305) 682 4430. After about 5:30 or 6
PM, that number becomes the BBS and you can reach him that way also. I'm
sure he'd be glad to pass on do's and don'ts, hints, etc.