This is an archive of CompuServe forum messages from 1985 to 1995, as saved in transcripts by John Foust.
Search Results (19 messages)
Bill, I was in on the auto-upgrade policy also and haven't moved. Could you please ship me the postcard also? If you haven't got my correct address I'll be glad to ship it to you. Thanks… John
Citizen Printer Driver
Message #1571
Hi All, Has anyone got or know of any printer drivers for Citizen Printers?? A friend of mine just purchased the GSX-140?? and is looking for a driver for it. Any help appreciated… Thanks John — 73647,1534
Thanks Robert, I'll try that tonight
Thanks Mike, I'll mail over a copy John
#C Question
Message #68155
Hi All… I'm trying to open a window and print some text and draw a couple of lines… Nothing major, but, if I open the window on workbench none of the text I pass to the TEXT function ever shows up on the screen, none of the lines I try…
Ok Greg, I'll bite, just what and how did you have to do to get the 1 meggers to run?? I've had my amiga for over 3 years now and really don't want to give it up for a 500 or 2000 if I don't have to.
Manx C 3.4 Question
Message #100653
Hi all, I'm writing a small routine to do a search on a file and upon reaching the } in a function the pc is being reset to 00000. NeNeedless to say my amy crashes soon after that. I traced the routine uusing db and the rts resets the program…
Thanks Gary, I've been linking with s.lib but the scr_ commands still do not clear screen, beep, clear to eol, or any of the other functions. If you can think of anything else I'd like to know. Thanks again… John 73647,1534
Aztec C Question
Message #94215
Hi all, how can I get the scr_ functions in the Aztec C compiler (vs. 3.4b) to work correctly?? The documentation says the programs must be linked using mixcroot or shcroot?? What and where are they and how do I link to them?? Any help at all would be appreciated.…
Aztec C Question
Message #93769
Hi all… I just picked up a copy of Aztec C and am trying to work with the SCREEN functions (scr_beep, scr_tab, etc) but they don't seem to work for me. I read in the manual (lib68.19) that I need to link with shcroot or mixcroot in order for these…
#Drive Alignment
Message #84809
Hi all, does anyone have any code that will check the alignment on the internal drive?? My drive is no longer reading valid floppies, I'm getting read/write errors all over the place. KS 1.2 stopped booting on my machine about 2 weeks ago, KS 1.1 stopped booting just today. I…
#NEC Disk Drive
Message #78380
I recently picked up a NEC 3 1/2 inch drive from a company called Halted Specialties. I'd like to hook this up to my Amiga as an eexternal drive but have not specs on the drive. I don't believe I I can use the pin-out specs for the 5 1/4…
#NEC Disk Drive
Message #78380
I recently picked up a NEC 3 1/2 inch drive from a company called Halted Specialties. I'd like to hook this up to my Amiga as an eexternal drive but have not specs on the drive. I don't believe I I can use the pin-out specs for the 5 1/4…
Hi Larry, No, as yet I have not. I'm trying to get some 3.5 drives to work on the system. I picked up the drives from a place called Halted Specialities for $89 each. The drives are bare (no casing) but it will not be too hard to shove several…
Internal 512k upgrade
Message #51096
Hi all, I've got the internal upgrade functioning ok. I had the downloads from here describing the upgrade but waited til I got my copy of Amazing before proceeding. Everything went very smoothly but watch how much space you put between your stacked memory chips, the daughter board must sit…
#External Drives
Message #44113
I've picked up an external drive from a company called Halted Specialties. The drive itself is the same drive used in the amiga but the company didn't have any documentation on the drive. Can anyone tell me what the pinouts are for the 34 pin connector on the back of…
TDI-Modula2
Message #44110
Hi all… Modula sure is neat, but I hit some kind of flako error. The following construct t := TRUNC(FLOAT(x) * c – FLOAT(x) * s) where t, and x are cardinals, and c and s are reals causes the machine to crash if x * c is a negative…
Mirage is an AMOS look-alike for 68000 based machines. I believe it came out of england several years ago and was available for the Sage (now Stride) Systems. I'm meeting with a guy this weekend to found out more about it so i'll post more when i know more. I…
Mirage is an AMOS look-alike for 68000 based machines. I believe it came out of england several years ago and was available for the Sage (now Stride) Systems. I'm meeting with a guy this weekend to found out more about it so i'll post more when i know more. I…