CompuServe Messages

Well, it's me again <g> Woe is me. I think I've got about 8 hairs left on my head! I think I've tried to do this about upteen times.(run Animator Pro under OS/2 2.2). So any help or (more) suggestions would help. Here is a message I left before; Help! Well, I've read the OS/2 Animator Pro messages, and I still can't get Animator Pro 1.3 to run under OS/2 2.1. I've tried using the default settings, with Animator running in full screen. No go! I've set the DPMI = Enabled, DPMI mem limit to 64 meg (tried 30meg and some other), Interupt during I/O to On; and still No go! I've tried to run it under a DOS window and DOS full screen and I get this error mesage: Abnormal program termination: Memory protection fault CS:EIP = 000Fh:000846F8h I've got a 486 66mghtz, 32 meg of RAM, STB Pegusas (S3928 chip), I've tried using the player for Animator, Aniplay, that does'nt work either. I have my system set up for dual boot, so I dual boot it to Dos. If I want to run Animator, but that gets to be a pain! But I'm thinking of switching over to the HPFS. Could there be something in my config.sys I have set up wrong? Any advice would be appreciated. Thanks to all! 🙂 Greg end of message. If I set my DPMI_MEMORY_LIMIT to 0 (Disabled) I get this message when I try to run Animator under a DOS full screen window; Phar Lap err 35: The 386 chip is currently executing in virtual 8086 mode under the control of another program. You must turn off this other program in order to use 386/DOS-Extender to run in protected mode. end of message I also have a Soundblaster 16ASP and a Toshiba CD rom, if that makes a difference. I use the Video drivers supplied by STB for the S3 chip. They are 16bit drivers. Whats the difference between 16bit and 32bit drivers. They don't have 32bit drivers. When I use my Dual Boot, (to boot to DOS) if I don't rem out the 5th line and try to run Animator, I get this on my screen: 062d) SYSTEM HALTED Then I have to reboot (DOS config.sys) DEVICE=C:\QEMM\DOSDATA.SYS DEVICE=C:\QEMM\QEMM386.SYS RAM ARAM=DB80-DBFF R:1 DEVICE=C:\QEMM\DOS-UP.SYS @C:\QEMM\DOS-UP.DAT DEVICE=C:\QEMM\LOADHI.SYS /R:3 C:\DOS\SETVER.EXE rem DEVICE=C:\QEMM\LOADHI.SYS /R:3 C:\QEMM\QDPMI.SYS SWAPFILE=DPMI.SWP SWAPSIZE=1024 Lastdrive=E DEVICE=c:\qemm\loadhi.sys /r:2 C:\TSCSI\MA13B.SYS DEVICE=c:\qemm\loadhi.sys /r:3 /res=10416 /sqf C:\TSCSI\TSLCDR.SYS /d:TSLCD SHELL=C:\QEMM\LOADHI.COM /R:2 C:\DOS\COMMAND.COM /P DOS=HIGH FILES=30 STACKS=0,0 SHELL=c:\qemm\loadhi.com /r:3 /res=3008 /sqf C:\dos\command.com C:\dos\ /P BUFFERS=10,0 end When I rem this line out, Animator Pro runs just fine (under DOS). Here is my OS/2 config.sys if it will help at all: IFS=C:\OS2\HPFS.IFS /CACHE:64 /CRECL:4 PROTSHELL=C:\OS2\PMSHELL.EXE SET USER_INI=C:\OS2\OS2.INI SET SYSTEM_INI=C:\OS2\OS2SYS.INI SET OS2_SHELL=C:\OS2\CMD.EXE SET AUTOSTART=PROGRAMS,TASKLIST,FOLDERS,CONNECTIONS SET RUNWORKPLACE=C:\OS2\PMSHELL.EXE SET COMSPEC=C:\OS2\CMD.EXE LIBPATH=.;C:\OS2\DLL;C:\OS2\MDOS;C:\;C:\OS2\APPS\DLL;C:\MMOS2\DLL;C:\OS2\SCRNSV \DLL; SET PATH=C:\OS2;C:\OS2\SYSTEM;C:\OS2\MDOS\WINOS2;C:\OS2\INSTALL;C:\;C:\OS2\MDOS;C:\ S2\APPS;C:\MMOS2; SET DPATH=C:\OS2;C:\OS2\SYSTEM;C:\OS2\MDOS\WINOS2;C:\OS2\INSTALL;C:\;C:\OS2\BITMAP; :\OS2\MDOS;C:\OS2\APPS;C:\MMOS2;C:\MMOS2\INSTALL; SET PROMPT=$i[$p] SET HELP=C:\OS2\HELP;C:\OS2\HELP\TUTORIAL;C:\MMOS2\HELP; SET GLOSSARY=C:\OS2\HELP\GLOSS; SET IPF_KEYS=SBCS PRIORITY_DISK_IO=YES FILES=20 DEVICE=C:\OS2\TESTCFG.SYS DEVICE=C:\OS2\DOS.SYS DEVICE=C:\OS2\PMDD.SYS BUFFERS=30 IOPL=YES DISKCACHE=1024,LW,AC:C MAXWAIT=3 MEMMAN=SWAP,PROTECT SWAPPATH=C:\OS2\SYSTEM 2048 2048 BREAK=OFF THREADS=256 PRINTMONBUFSIZE=134,134,134 COUNTRY=001,C:\OS2\SYSTEM\COUNTRY.SYS SET KEYS=ON REM SET DELDIR=C:\DELETE,512; BASEDEV=PRINT01.SYS BASEDEV=IBM1FLPY.ADD BASEDEV=IBM1S506.ADD BASEDEV=OS2DASD.DMD SET BOOKSHELF=C:\OS2\BOOK;C:\MMOS2; SET EPMPATH=C:\OS2\APPS; REM DEVICE=C:\OS2\APPS\SASYNCDA.SYS PROTECTONLY=NO SHELL=C:\OS2\MDOS\COMMAND.COM C:\OS2\MDOS FCBS=16,8 RMSIZE=640 DEVICE=C:\OS2\MDOS\VEMM.SYS DOS=LOW,NOUMB DEVICE=C:\OS2\MDOS\VDPX.SYS DEVICE=C:\OS2\MDOS\VXMS.SYS /UMB DEVICE=C:\OS2\MDOS\VDPMI.SYS DEVICE=C:\OS2\MDOS\VCDROM.SYS REM DEVICE=C:\OS2\PCMCIA.SYS REM DEVICE=C:\OS2\MDOS\VPCMCIA.SYS CODEPAGE=437,850 DEVINFO=KBD,US,C:\OS2\KEYBOARD.DCP REM DEVICE AND RUN STATEMENTS FROM YOUR OLDER CONFIG.SYS REM DEVICE=C:\DOS\SETVER.EXE REM DEVICE=C:\DOS\HIMEM.SYS REM DOS=HIGH DEVINFO=SCR,BGA,C:\OS2\VIOTBL.DCP SET VIDEO_DEVICES=VIO_VGA DEVICE=C:\OS2\MDOS\VMOUSE.SYS DEVICE=C:\OS2\POINTDD.SYS DEVICE=C:\OS2\MOUSE.SYS SERIAL=COM0 IFS=\OS2\CDFS.IFS /Q BASEDEV=OS2SCSI.DMD BASEDEV=T13BSCSI.ADD DEVICE=C:\OS2\OS2CDROM.DMD /Q DEVICE=C:\MMOS2\SB16D2.SYS 1 1 5 5 220 8 /N:SBAud1$ DEVICE=C:\MMOS2\AUDIOVDD.SYS SBAud1$ SET MMBASE=C:\MMOS2; SET DSPPATH=C:\MMOS2\DSP; SET NCDEBUG=4000 DEVICE=C:\MMOS2\SSMDD.SYS DEVICE=C:\MMOS2\ADSHDD.SYS DEVICE=C:\MMOS2\SMVDD.SYS SET VIO_VGA=DEVICE(BVHVGA,BVHENH) DEVICE=C:\OS2\MDOS\VVGA.SYS DEVICE=C:\OS2\MDOS\VWIN.SYS DEVICE=C:\OS2\MDOS\VENH.SYS REM DEVICE=C:\OS2\COM.SYS REM DEVICE=C:\OS2\MDOS\VCOM.SYS DEVICE=C:\OS2\COM.SYS DEVICE=C:\OS2\MDOS\VCOM.SYS end of OS/2config.sys See, I want to switch over to the HPFS, I don't like to Dual boot just to run Animator Pro <pain> Thanks for any suggestions or help Sorry If I'm a pain. I just want to keep these last 8 hairs on my Head! confused:-( Greg