CompuServe Thread

#Slides

10 messages in this thread
#4698From: Tom Patrick McAuliffeApr 15, 1995 2:09 PM
Hi, What's the best way to convert slides to video tape without spending a fortune? TP
#4712From: James Bell Jr.Apr 15, 1995 7:45 PM
Take a look at the Tamron FOTOVIX IIIS. It provides S-Video and composite video outputs, and accepts both slides and negatives. You can find a review of the unit under the filename FOTVIX.TXT in Library 2 of this forum. The unit can be obtained via mail order from B&H Photo and other resellers. James Bell Jr. — Multimedia Contributor – CompuServe
#4726From: Tom Patrick McAuliffeApr 16, 1995 1:36 PM
Yea but at $699 its a bit outta my price range. Any other ideas? Thnks, TP
#4732From: James Bell Jr.Apr 16, 1995 6:38 PM
There are some adapters made to go on the front of a standard camcorder which accept slides, the intent being to videotape the slides. Most of the results I have seen from these have been pitiful. I did see one, used with a Sony CCD-V5000, which worked very well. The V5000 has a manual white-balance which I believe was the primary factor for the good video. Aside from the Fotovix IIIS, these adapters are your only option for do-it-yourself slide to video conversion. You can always have them sent to a service bureau for conversion, but then you don't have direct control over the appearance, something I consider to be vital. James Bell Jr. — Multimedia Contributor – CompuServe P.S. Based on your work, you should have access to a VGA to NTSC converter. It is possible to put the slides on a Photo-CD and send that out to videotape through the PC. If you don't have the VGA to NTSC converter, you could go buy a CD-i Player and use that to transfer the images. Take a look at TMTE01.PDF and TMTE02.PDF in Library 2 of this forum for more details on CD-i players. Either of these options may cost less than $699.00, depending on how many slides you have. The image won't be as good as the Fotovix IIIs, but it would work.
#4922From: Tom Patrick McAuliffeApr 23, 1995 8:04 PM
Thank you so much…. Why didn't I think of that! TP
#4739From: henry tellerApr 16, 1995 10:28 PM
Hello Again Tom – You could set up a copy stand with a light box and camera with a macro lens. That's the basics of the Fotovix. Ambient light could be a problem, but then you'll be able to see the image before you freeze it into the computer. If you run the video through a TBC, you would have better control over the final image. Hank Videology, Inc Where service is our product
#4746From: John SmallApr 17, 1995 11:07 AM
What does the TBC do? Thanks. -jts
#4765From: henry tellerApr 17, 1995 11:03 PM
Beside the video controls on your camera, the TBC (like the DPS TBC IV) provides proc amp controls of HSV, video signal, color balance, etc. for color correcting the still frame. This would be one way of tweaking the image before capture. Hank Videology, Inc Where service is our product
#4923From: Tom Patrick McAuliffeApr 23, 1995 8:05 PM
Tks, TP
#4747From: John SmallApr 17, 1995 11:07 AM
Take a look at SLDVID.TXT in DIVING, Lib 7. Tells how to use your projector and screen to capture slides. Others have said this works well. I haven't tried yet but will since I have a ton to move over to tape when the mood strikes. -jts