This is an archive of CompuServe forum messages from 1985 to 1995, as saved in transcripts by John Foust.
Search Results (25 messages)
Thanks Mr. Watje for the info. I am rendering a flic file. bye Dan Pasholk
#RESTART RENDERING ?
Message #185608
Hello: How can I start and stop then restart a rendering without losing what has already been rendered? I have the computer set up as a stand alone network station. Any information would be most welcome. Thank you for your help. Daniel Pasholk /exit
#3dsr4 modeler
Message #129007
Hello Autodesk: Now that the spline-based modeler is no longer included with r4 upgrade, is there any way to get a beta version? What are the reasons it was taken out? Please be so kind and post a response for all to read. Thanks Daniel 'Dare' Pasholk
spline-modeler 3dsr4
Message #128893
Hello Autodesk: Now that the Spline-Based Modeler is no longer included with the r4 upgrade , is it at all possiable to get a beta version? What is the requirements to become a beta tester? Any information on why it was taken out? Thanks Daniel 'Dare' Pasholk
#spline-modeler 3dsr4
Message #128359
Hello Adesk: 3dsr4's Preliminary Technical specifications shows an feature called a Spline-Based Modeler. Will this still be included in this upgrade? If not, will there be any additional cost when it is available? Thanks Daniel 'Dare' Pasholk 12400 N81NC:\ORCADcompuserve………….9 953-9680…2400 E71NCOMPSPSMOTOROLA……………
#glassfra
Message #109325
I have been trying to model a faceted clear glass object and haven't been able to get the facet reflecting effect of individual facets or model realistically looking through glass onto interior facets. My question therfore is: Will future versions of 3DS have in the materials editor a provision to…
Thanks for the help. bye for now. Daniel Pasholk
tablet
Message #103470
Hello I am using a Summa Sketch tablet for my pointing input device. In 3DS3 under 'Info \ Configure \ Tablet \ Area ' I can set the active pointing area, but when I exit I loose the setting. Is there a was to keep this setting? Also, is there…
Thanks Mr. Elliott Will there be any further 3ds workshops at Moraine valley ? bye for now. Daniel Pasholk
GIFDXF
Message #101032
hello In the new book 'Inside 3d studio' on page 992 there is reference to a program GIFDXF. Where would it be located. Thanks for any help Daniel Pasholk
#Designer/3ds
Message #92886
Hi Does Autocad Designer have the ability to write .3ds files directly? Any information would be most welcome. Thank you Daniel Pasholk
Payne Enterprises Sirs: Thanks for the information. Hope to get your product very soon. Daniel 'Dare' Pasholk
#Mirage Raytracing
Message #67534
Hello: Has anybody have experiance using the "Mirage Raytracing Engine" ? Looking for pros, cons, features. Any comments would be most wecome. Thanks Daniel 'Dare' Pasholk
Please to include me also to the 3DS Magazine. Daniel Pasholk 118 Saugatuck Montgomery Il 60538 Thanks for the most welcome addition.
hp postscript
Message #61188
Hello 3ds: Is there a RHPADI driver for the HP laser jet 4. I would like to make a postscript file of a 3ds image and get a hardcopy. Thanks for any information about this topic. Daniel Pasholk
ripple cone
Message #56651
Hello: Is there some helpful hints and tips out there which could help me out? I would like to use the ripple program on a cone. I want the cone to stay put and have a succession of wave travel from the tip to the base. Your help is very…
#replay
Message #55478
All When replaying a FLI the file runs off of the hard drive. The size of the file is 2meg and I have 16meg of ram. I made a Ramdrive and put the file there and it played fine, no hard drive access. Is there a setting in 3DS which…
Thanks for the help, I'll give it a try. Daniel 'Dare' Pasholk
#Vports-UCS
Message #52303
Hello I would like to know if the AutoCad screen could be set up the same as 3DS. In AutoCad, I would have the 4 vports, but each vport would have it's own UCS. And each time I would change vports the UCS assigned to that vport would stay. The…
Dear Mr. Pyros I would like to be on the mailing list to receive the 3DS Newsletter. I will be happy to subscribe and be a loyal reader of the newsletter. Please send to : Daniel Pasholk 118 saugatuck Montgomery, IL 60538 Thanks for providing this much needed newsletter.
Thank very much for the information. Daniel Pasholk
Thanks for the invite, hope to be there. Dan Pasholk
David, yes, please more details about the Milwaukee 3DS users group. Thanks for the info. Dan Pasholk
Hi How about 3DS user group in the Chicago area? Thanks Dan 'Dare' Pasholk
3d-threads
Message #4438
Looking for and autolisp program which will create 3D threads or springs. Maybe a Helix lisp program? Thanks Dan P. GE…..D