This is an archive of CompuServe forum messages from 1985 to 1995, as saved in transcripts by John Foust.
Search Results (18 messages)
Hi thomas, I use AFSpro for more than a month now, The difference between both versions is that the normal version only supports one harddisk an is limited to max 650MB, The AFSpro version has no limits, includes MultiUser Filesystem support, and an utilitie to convert the FFSpartitions to AFSpartitions…
Your welcome pal ! Salu2 Juan Ferrin From Belgium with Autopilot
Ray, Does the program accepts TOOLTYPES ??? You could check this out running snoopdos on the background while starting the program… Regards, Juan Ferrin From Belgium with Autopilot
Hi Jerry, If you want to format a HardDisk using the HDtoolbox you have to start HDtoolbox with parameters to force HDToolbox to search for the 'device' example: "HDtoolbox z3scsi.device" (for Fastlane Z3controller) or "HDtoolbox suprascsi.device" (for the supracontrollers) or "HDtoolbox warpdrive.device" (for the Macrosystems Warp card) so you have…
Hi Tom, PFMJI, I use AFS for 4 weeks now, and i am verry happy with it. When programs crashes or there occure power outages, while you was writing to an AFS partition nothing bad happens, the partition allways remains validated, of course the file you was writing at the…
Thanks for the info Faust, I will continue using my HPL4 instead of my Kyocera for printing with TeX. At least now I Know that nothing is wrong with my setup. Since my Fyocera has a "Prescribe" command set I will try lowering the setting for the max download and…
Bryan, PFMJI, The latests version of Octamed (V6.0) supports the Toccata… Regards, Juan From Belgium with Autopilot
Tag Michael, Erfreut dich hier su sehen…. So you are the writer of that book, i bought it a year ago, (Amiga Messe Koln), and it has his own place next to my keyboard !!! Placed your Email address in my address book, just for in case…:-) BTW, ist das…
Bryan, If you plan to purchase the VLAB-M system you may not forget you wil need a fast scsi controller, y hope you are using a A3000 with 2.1, upgrade to 2.1 is not necesary vor the Movieshop software but i higly recommend it !! If you use a A2000…
Les, There it comes, Regards, Juan Ferrin From Belgium with Autopilot
Maybe you can use the "reboot" program from Workbench3.1 its located in the C: directory of the Install3.1 disk. Regards. *** Juan Ferrin From Belgium with AUTOPILTO V1.8 ***
Jose ?? Hmmm sound spanish to me…. 🙂 Check jumper J351 on your motherboard, J351: DF1 Enable Closed: Enable low-density (880K) floppy as DF1. Open: No DF1 *OR* for high-density (1.76M) DF1. Good luck, *** Juan Ferrin from Belgium with AUTOPILOT V1.8 ***
Keith, Lucky you i have the same CDRom drive, and put my manual in a safe place… The users manual say this: Jumper number 1 is on the LEFT side of the block….. Jumpers are preset at factory with J1 & J5 enabled…. Jumpers 1,2,3 => SCSI ID Jumper 4…
Clinton, You could try to get information from the European Amiga Repair Center: DCE Computer Service GmbH Kellenbergerstra_e 19 a 46145 Oberhausen Germany Tel: ( )208 633151 Fax: ( )208 630496 They do these kind of reworks for us… *** Juan Ferrin from Belgium with AUTOPILOT V1.8 ***
Thanks for the information *** Juan Ferrin from Belgium with AUTOPILOT V1.8 ***
Hola Rafa, tienes razon, es Juan Ferrin, Espaqol de 36 aqos, casado con Montse, tengo un hijo de 16 (Jairo) y una hija de 12 (Diana), y…PENSIONADO..(lla te contare esto en otra ocasion). Cuentame de ti a que te dedicas…?? Yo como tengo todo el dia libre puedo dedicar mucho…
#SONNET 68040/50Mhz
Message #208541
He out there, Does somebody heard about the SONNET 68040/50 Mhz board…???? Would like to here some advice, since I am planning to buy it. *** Ferrin Juan from Belgium with AUTOPILOT V1.8 ***
#GVP040/A3000 lockups
Message #208216
Sorry for have upset you, My reliabel source happens to be 'Herr Dellert' chief of the European AMIGA Repair Center in Germany and the technical staff of GVP Germany… Why would they lei to me.??? If these people are not reliabel enough for you, you may forget what i said.…